INTRODUCTION
ISO stands for the International Standardisation Organisation which is an independent body for the development and publishing of International Standards. ISO is a network of the National Standards Institutes in more than 160+ countries with one member per country and a Central Secretariat in Geneva, Switzerland that coordinates the system. ISO is a Non-Government Organisation that forms a bridge between the Public and Private sectors for the development of standards and norms for different industries.
This blog post is a summary of all the standards that were published by the International Organisation of Standardisation.
SERIES FROM ISO 1 TO ISO 99
- ISO 8:1977 Documentation – Presentation of periodicals.
- ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters into Latin characters – Slavic and non-Slavic languages.
- ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins.
- ISO 12:1987 Aerospace – Pipelines – Identification.
- ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering – Dimensions, tolerances and verification.
- ISO 15:2011 Radial bearings—Boundary dimensions, general plan.
- ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch).
- ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers.
- ISO 18:1981 Documentation – Contents list of periodicals.
- ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor chains.
- ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys – Dimensions and tolerances.
- ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—Specifications.
- ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—Specifications.
- ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for direct front projection—Specifications.
- ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture film—Specifications.
- ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-picture film for direct front projection—Specifications [Withdrawn without replacement].
- ISO 31 Quantities and units [withdrawn: replaced with ISO/IEC 80000].
- ISO 32:1977 Gas cylinders for medical use—Marking for identification of content.
- ISO 34
- ISO 34-1:2010 Rubber, vulcanized or thermoplastic—Determination of tear strength—Part 1: Trouser, angle and crescent test pieces.
- ISO 34-2:2011 Rubber, vulcanized or thermoplastic—Determination of tear strength—Part 2: Small (Delft) test pieces.
- ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability.
- ISO 36:2011 Rubber, vulcanized or thermoplastic—Determination of adhesion to textile fabrics.
- ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties.
- ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps [withdrawn without replacement].
- ISO 43:1976 Aircraft—Jacking pads.
- ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—Directions of operation.
- ISO 45:1990 Aircraft—Pressure refueling connections.
- ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets.
- ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100 IRHD).
- ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1.
- ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 [Withdrawn without replacement].
- ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile.
- ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—Modules.
- ISO 55:1977 Seedlac—Specification [Withdrawn without replacement].
- ISO 57:1975 Bleached lac—Specification [Withdrawn without replacement].
- ISO 60:1977 Plastics—Determination of apparent density of the material that can be poured from a specified funnel.
- ISO 61:1976 Plastics—Determination of apparent density of molding material that cannot be poured from a specified funnel.
- ISO 62:2008 Plastics—Determination of water absorption.
- ISO 63:1975 Flat transmission belts—Lengths [Withdrawn: Replaced with ISO 22].
- ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1.
- ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size [Withdrawn without replacement].
- ISO 68 ISO general-purpose screw threads – Basic profile.
- ISO 68-1:1998 Metric screw threads.
- ISO 68-2:1998 Inch screw threads.
- ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting and perforating dimensions.
- ISO 70:1981 Cinematography—35 mm negative photographic sound record on 35 mm motion-picture film—Position and maximum width dimensions.
- ISO 71:1977 Cinematography—16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions.
- ISO 74:1976 Cinematography—Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film—Positions and dimensions.
- ISO 75 Plastics—Determination of temperature of deflection under load.
- ISO 75-1:2013 Plastics—Determination of temperature of deflection under load—Part 1: General test method.
- ISO 75-2:2013 Plastics—Determination of temperature of deflection under load—Part 2: Plastics and ebonite.
- ISO 75-3:2004 Plastics—Determination of temperature of deflection under load—Part 3: High-strength thermosetting laminates and long-fiber-reinforced plastics.
- ISO 76:2006 Rolling bearings—Static load ratings.
- ISO 78 Chemistry — Layouts for standards.
- ISO 78-2:1999 Chemistry—Layouts for standards—Part 2: Methods of chemical analysis.
- ISO 78-3:1983 Chemistry—Layouts for standards—Part 3: Standard for molecular absorption spectrometry.
- ISO 78-4:1983 Layouts for standards—Part 4: Standard for atomic absorption spectrometric analysis.
- ISO 82:1974 Steel—Tensile testing [Withdrawn: replaced with ISO 6892-1].
- ISO 83:1976 Steel—Charpy impact test (U-notch) [Withdrawn: replaced with ISO 148-1].
- ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than 0.5 mm thick [Withdrawn: replaced with ISO 6892-1].
- ISO 89:1974 Steel—Tensile testing of wire [Withdrawn: replaced with ISO 6892-1].
- ISO 90 Light gauge metal containers—Definitions and determination of dimensions and capacities.
- ISO 90-1:1997 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 1: Open-top cans.
- ISO 90-2:1997 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 2: General use containers.
- ISO 90-3:2000 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 3: Aerosol cans.
- ISO 91 Petroleum measurement tables.
- ISO 91-1:1992 Petroleum measurement tables—Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F.
- ISO 91-2:1991 Petroleum measurement tables—Part 2: Tables based on a reference temperature of 20 degrees C.
- ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of side (left or right).
- ISO 93 Textile machinery and accessories—Cylindrical sliver cans.
- ISO 93-1:2006 Textile machinery and accessories—Cylindrical sliver cans—Part 1: Main dimensions.
- ISO 93-2:2006 Textile machinery and accessories—Cylindrical sliver cans—Part 2: Spring bottoms.
- ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning and ring-doubling frames.
- ISO 96 Textile machinery and accessories—Rings and travelers for ring spinning and ring twisting frames.
- ISO 96-1:2009 Textile machinery and accessories—Rings and travelers for ring spinning and ring twisting frames—Part 1: Flange rings T and SF and their travelers.
- ISO 96-2:2009 Textile machinery and accessories—Rings and travelers for ring spinning and ring twisting frames—Part 2: HZ- and J-rings and their travelers.
- ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and twisting for ear-shaped travelers.
- ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning machinery—Main dimensions of coverings for top rollers.
- ISO 8:1977 Documentation – Presentation of periodicals.
- ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters into Latin characters – Slavic and non-Slavic languages.
- ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins.
- ISO 12:1987 Aerospace – Pipelines – Identification.
- ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering – Dimensions, tolerances and verification.
- ISO 15:2011 Radial bearings—Boundary dimensions, general plan.
- ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch).
- ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers.
- ISO 18:1981 Documentation – Contents list of periodicals.
- ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor chains.
- ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys – Dimensions and tolerances.
- ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—Specifications.
- ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—Specifications.
- ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for direct front projection—Specifications.
- ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture film—Specifications.
- ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-picture film for direct front projection—Specifications [Withdrawn without replacement].
- ISO 31 Quantities and units [withdrawn: replaced with ISO/IEC 80000].
- ISO 32:1977 Gas cylinders for medical use—Marking for identification of content.
- ISO 34
- ISO 34-1:2010 Rubber, vulcanized or thermoplastic—Determination of tear strength—Part 1: Trouser, angle and crescent test pieces.
- ISO 34-2:2011 Rubber, vulcanized or thermoplastic—Determination of tear strength—Part 2: Small (Delft) test pieces.
- ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability.
- ISO 36:2011 Rubber, vulcanized or thermoplastic—Determination of adhesion to textile fabrics.
- ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties.
- ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps [withdrawn without replacement].
- ISO 43:1976 Aircraft—Jacking pads.
- ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—Directions of operation.
- ISO 45:1990 Aircraft—Pressure refueling connections.
- ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets.
- ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100 IRHD).
- ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1.
- ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 [Withdrawn without replacement].
- ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile.
- ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—Modules.
- ISO 55:1977 Seedlac—Specification [Withdrawn without replacement].
- ISO 57:1975 Bleached lac—Specification [Withdrawn without replacement].
- ISO 60:1977 Plastics—Determination of apparent density of the material that can be poured from a specified funnel.
- ISO 61:1976 Plastics—Determination of apparent density of molding material that cannot be poured from a specified funnel.
- ISO 62:2008 Plastics—Determination of water absorption.
- ISO 63:1975 Flat transmission belts—Lengths [Withdrawn: Replaced with ISO 22].
- ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1.
- ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size [Withdrawn without replacement].
- ISO 68 ISO general-purpose screw threads – Basic profile.
- ISO 68-1:1998 Metric screw threads.
- ISO 68-2:1998 Inch screw threads.
- ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting and perforating dimensions.
- ISO 70:1981 Cinematography—35 mm negative photographic sound record on 35 mm motion-picture film—Position and maximum width dimensions.
- ISO 71:1977 Cinematography—16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions.
- ISO 74:1976 Cinematography—Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film—Positions and dimensions.
- ISO 75 Plastics—Determination of temperature of deflection under load.
- ISO 75-1:2013 Plastics—Determination of temperature of deflection under load—Part 1: General test method.
- ISO 75-2:2013 Plastics—Determination of temperature of deflection under load—Part 2: Plastics and ebonite.
- ISO 75-3:2004 Plastics—Determination of temperature of deflection under load—Part 3: High-strength thermosetting laminates and long-fiber-reinforced plastics.
- ISO 76:2006 Rolling bearings—Static load ratings.
- ISO 78 Chemistry — Layouts for standards.
- ISO 78-2:1999 Chemistry—Layouts for standards—Part 2: Methods of chemical analysis.
- ISO 78-3:1983 Chemistry—Layouts for standards—Part 3: Standard for molecular absorption spectrometry.
- ISO 78-4:1983 Layouts for standards—Part 4: Standard for atomic absorption spectrometric analysis.
- ISO 82:1974 Steel—Tensile testing [Withdrawn: replaced with ISO 6892-1].
- ISO 83:1976 Steel—Charpy impact test (U-notch) [Withdrawn: replaced with ISO 148-1].
- ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than 0.5 mm thick [Withdrawn: replaced with ISO 6892-1].
- ISO 89:1974 Steel—Tensile testing of wire [Withdrawn: replaced with ISO 6892-1].
- ISO 90 Light gauge metal containers—Definitions and determination of dimensions and capacities.
- ISO 90-1:1997 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 1: Open-top cans.
- ISO 90-2:1997 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 2: General use containers.
- ISO 90-3:2000 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 3: Aerosol cans.
- ISO 91 Petroleum measurement tables.
- ISO 91-1:1992 Petroleum measurement tables—Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F.
- ISO 91-2:1991 Petroleum measurement tables—Part 2: Tables based on a reference temperature of 20 degrees C.
- ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of side (left or right).
- ISO 93 Textile machinery and accessories—Cylindrical sliver cans.
- ISO 93-1:2006 Textile machinery and accessories—Cylindrical sliver cans—Part 1: Main dimensions.
- ISO 93-2:2006 Textile machinery and accessories—Cylindrical sliver cans—Part 2: Spring bottoms.
- ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning and ring-doubling frames.
- ISO 96 Textile machinery and accessories—Rings and travelers for ring spinning and ring twisting frames.
- ISO 96-1:2009 Textile machinery and accessories—Rings and travelers for ring spinning and ring twisting frames—Part 1: Flange rings T and SF and their travelers.
- ISO 96-2:2009 Textile machinery and accessories—Rings and travelers for ring spinning and ring twisting frames—Part 2: HZ- and J-rings and their travelers.
- ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and twisting for ear-shaped travelers.
- ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning machinery—Main dimensions of coverings for top rollers.
No comments:
Post a Comment